Ground shafts
Precision ground round shafts in standard metric and inch diameters and lengths, to go with your gears. They ship with your printed parts. A gear with a set-screw hub (the generator's standard) locks onto them.
| Material | 303 stainless steel; 3, 4 and 5 mm in carbon steel |
| Finish | Ground |
| Diameter tolerance | Metric −0.005 to 0 mm (stainless); inch −0.0005 to 0" |
| Lengths | Metric 100, 200 and 400 mm; inch 4, 6 and 12" |
| Availability | In stock where a price is shown |
Metric shafts
Part number by diameter and length
| Diameter | 100 mm | 200 mm | 400 mm |
|---|---|---|---|
| 2 mmD-flat: 1.5 mm across | PG-SM2-100 | PG-SM2-200 | PG-SM2-400 |
| 3 mmD-flat: 2.5 mm across | PG-SM3-100 | PG-SM3-200 | PG-SM3-400 |
| 4 mmD-flat: 3.5 mm across | PG-SM4-100 | PG-SM4-200 | PG-SM4-400 |
| 5 mmD-flat: 4.5 mm across | PG-SM5-100 | PG-SM5-200 | PG-SM5-400 |
| 6 mmD-flat: 5.5 mm across | PG-SM6-100 | PG-SM6-200 | PG-SM6-400 |
| 8 mmD-flat: 7.5 mm across | PG-SM8-100 | PG-SM8-200 | PG-SM8-400 |
| 10 mmD-flat: 9 mm across | PG-SM10-100 | PG-SM10-200 | PG-SM10-400 |
| 12 mmD-flat: 11 mm across | PG-SM12-100 | PG-SM12-200 | PG-SM12-400 |
Inch shafts
Part number by diameter and length
| Diameter | 4" | 6" | 12" |
|---|---|---|---|
| 1/8"D-flat: 0.105" across | PG-SI125-4 | PG-SI125-6 | PG-SI125-12 |
| 3/16"D-flat: 0.168" across | PG-SI188-4 | PG-SI188-6 | PG-SI188-12 |
| 1/4"D-flat: 0.230" across | PG-SI250-4 | PG-SI250-6 | PG-SI250-12 |
| 5/16"D-flat: 0.293" across | PG-SI313-4 | PG-SI313-6 | PG-SI313-12 |
| 3/8"D-flat: 0.345" across | PG-SI375-4 | PG-SI375-6 | PG-SI375-12 |
| 1/2"D-flat: 0.470" across | PG-SI500-4 | PG-SI500-6 | PG-SI500-12 |
Fitting a printed gear to a shaft
On a round shaft, give the gear a set-screw hub: the generator's standard hub has a brass heat-set insert and a cup-point set screw, so the screw bears on the shaft without threading into the nylon. Choose the shaft size under Hub & bore and leave the fit at Sliding. For a motor with a D-flat shaft, choose a D-flat bore instead.
Making your own D-flat. With a surface or bench grinder you can grind a flat on any of these shafts. Grind it to the across-flat size shown under each diameter, the standard D-shaft size, at least as long as the gear's bore and hub, and break the edges. Then choose a D-flat bore of that diameter in the generator: its bore matches that flat. A D-flat carries more torque than a set screw on a round shaft, and the set-screw insert sits over the flat. More in Mounting nylon gears.