Mounting nylon gears
For most printed gears the answer is simple: a D-flat bore with a sliding fit on a ground D-profile shaft, held along the shaft by a shoulder, collar or e-clip. The flat carries the torque. Nothing digs into the nylon, and the gear comes off again when you need it to.
- Shoulder on the shaft (or a collar) locates the gear and takes axial thrust.
- Gear, printed with a D-bore 0.1 mm larger than the shaft, so it slides on.
- E-clip in a groove, or a second collar, keeps the gear from walking off.
- Ground D-profile shaft, as on most small motors.
- The flat. Torque is carried by its contact with the matching flat in the bore.
Our recommendation
- D-bore on a D-profile shaft for nearly everything. In the generator, choose D-flat under Hub & bore, pick the shaft from the size menu and leave the fit at Sliding. Standard D-shaft sizes, such as the common 5 mm stepper shaft, are in the menu. You can also grind a flat on a round ground shaft yourself: grind it to the across-flat size listed there and the generator's D-bore matches it.
- Double-D or hex for reversing or higher torque. More flank area, and two flats share the load.
- Bolted to a metal hub when the torque is more than the nylon around the bore can take.
Set screws, done right
A set screw threaded straight into nylon strips or creeps loose. Threaded into a brass heat-set insert, it holds. In the generator, choose a set-screw insert under Hub & bore. The hub is sized for it, and the first insert sits over the D flat, so the screw bears on the flat and can't raise a burr where the gear slides. We support standard brass heat-set inserts in M2 to M5 and 4-40 to 8-32. Order the gear with the inserts installed and we press them in and supply stainless cup-point set screws of the right length; or order the holes only and fit your own (the generator names a matching insert).
Don't overtighten. The set screw's clamping force pushes back on the insert, and nylon holds it less firmly than metal would. Tighten to no more than about 0.25 N·m for M3 and 4-40, 0.35 N·m for 6-32, 0.6 N·m for M4 and 8-32, and 1 N·m for M5: about half what you would use in steel. With a short hex key, that is a firm twist of the fingers, not a wrench on the long arm. A drop of medium threadlocker on the screw holds better than extra torque.
Holding the gear along the shaft
A D-bore stops rotation but not sliding. Spur gears push only lightly along the shaft. Helical and bevel gears push hard, because their teeth make an axial thrust. Put a shoulder or collar on the side the thrust pushes toward, and an e-clip or second collar on the other side. A hub boss gives a collar or clip something wide to bear on.
Choosing the fit
- Sliding, +0.10 mm. The default. Slides on by hand with a little resistance.
- Light press, +0.05 mm. Pushes on firmly and won't rattle. Use for gears you won't remove often.
- Glued, +0.15 mm. Leaves room for a thin, even layer of adhesive.
Laser-sintered holes come out slightly small and vary by a few hundredths of a millimetre. If a fit matters, order one gear first and adjust.
Permanent joints: the heat-pressed knurled shaft
For a gear that must never move, print a round bore about 0.15 mm under the shaft size and press in a shaft with a straight-knurled end, heated to around 200 °C. The nylon around the knurl softens, flows into the grooves and locks when it cools. Heat the shaft, not the gear: a hot-air gun on a printed gear warps it before the bore expands enough to help.
Press steadily and straight, in one stroke, with the gear supported on a flat plate. Let it cool before loading it.
Adhesives
Glue is a backup, not the main torque path, because nylon is hard to bond. If you use it, methyl methacrylate structural adhesives such as 3M DP8910NS or Plexus bond nylon best. Cyanoacrylate with a polyolefin primer is next, then a flexible epoxy. Anaerobic retaining compounds don't cure properly against nylon. Roughen the bore and clean the shaft first.
What to avoid
- Set screws threaded straight into the nylon. They strip, or creep loose. A set screw is fine in a brass threaded insert, bearing on the shaft's flat.
- A plain round bore held only by a tight fit. Nylon creeps, and the grip fades within weeks.
- Shrink fits made by heating the gear. The interference you can get from nylon's expansion is smaller than the print tolerance.
The generator defaults to a 5 mm D-bore with a sliding fit. Pick another shaft from the size menu. Open the generator.