About & FAQ
Protogears makes custom gears in the Chicago area. We wrote the generator on this site because getting the tooth form right matters, and most free tools only approximate it.
How the profiles are made
The generator simulates a standard basic rack rolling against the gear blank, the way a hob or shaper cutter forms real teeth. You get the true involute flank, the trochoidal root fillet and any undercut on small tooth counts. We checked the flanks against the analytic involute and the over-pins dimension against a direct fit to the generated profile; both agree to well under a micron.
Questions
What are the printed gears made of?
Nylon 12 (PA2200) by selective laser sintering, in natural white. It is tough and wears well against itself and against metal. Use it for prototypes, fit checks, instruments, models and light-duty mechanisms. For high torque, high speed or high temperature, use metal gears.
How accurate are they?
We are calibrating our process against measured test gears and will publish tolerance figures here when that work is done. Every order ships with a spec sheet giving the nominal over-pins and span measurements, so you can check the parts yourself.
What can I order?
- Spur and helical gears, double (cluster) gears, matched gear pairs, racks with their pinion, and internal (ring) gears with their pinion, at a 20°, 14.5° or 25° pressure angle, or a custom angle
- Module 0.5 to 5 mm (about 50 to 5 diametral pitch), 6 to 200 teeth, up to 170 mm outside diameter
- Face width 3 to 50 mm; for double gears, both faces together up to 50 mm
- Round, keyed, D-flat, double-D, hex or square bores (2 mm and up), hubs on one or both sides, bolt circles and spoked windows
- Racks up to 220 mm long; ring gears up to 170 mm rim diameter
How long does it take?
Orders ship in 7 to 10 business days. We batch prints, so larger quantities don't take much longer.
How does gear pair mode work?
Enter the two tooth counts and either the center distance you need or the profile shifts you want. In center-distance mode the generator finds the shift sum and splits it so the smaller gear avoids undercut, then optionally shortens the tips to keep standard root clearance. It reports working pressure angle, contact ratio, backlash and clearances. It also checks whether either gear's tips would run below the other gear's true involute, a problem many calculators miss on small pinions. The mesh is checked against the actual generated tooth shapes: at the computed center distance the teeth touch with zero clearance when no backlash is specified.
How are ring gears made?
Ring gears can't be cut with a rack, so the generator simulates a pinion-type shaper cutter rolling inside the blank, which is how ring gears are cut in practice. It picks a cutter size that keeps the ring teeth fully involute. It can also shorten the ring tips so they stay on the pinion's involute, a common source of noise and wear in ring-and-pinion sets. Measurement between pins is computed on the generated profile.
Do you support helical gears?
Yes. Enter the normal module (or normal diametral pitch), the helix angle and the hand; gear pairs get opposite hands automatically. The generator reports the transverse module, lead, overlap ratio and total contact ratio. The load rating uses the ISO virtual spur gear, with the helix and contact-ratio factors, and reports the axial thrust for bearing selection. The STL carries the full helix. STEP export for helical gears is coming.
How are the load ratings calculated?
Root bending follows ISO 6336-3 method B. The critical section at the 30° tangent, the load arm and the load angle are measured on the generated tooth, so backlash thinning, profile shift and tip shortening are all included. The fillet radius comes from the ISO closed form. At zero backlash the result matches the ISO closed form to about 0.01%, and the tooth form factors agree with the published ISO charts. For gear pairs, the contact stress follows ISO 6336-2 at the pitch point, using the contact ratio actually achieved. Material allowables are editable starting values, not guaranteed data; plastic gears in particular depend on temperature, lubrication, moisture and cycle count (VDI 2736 is a good reference).
What files do I get?
STEP (AP214) solid models for spur gears, double gears, racks and ring gears. These are true B-rep solids with cylindrical and planar faces, validated with the OpenCascade CAD kernel. DXF (R12, one layer per gear and bore) built from true arcs that stay within 0.001 mm of the generated profile, about a dozen arcs per tooth, which CAM software handles far better than thousands of tiny segments. A dense-polyline option is there if you prefer it. You also get SVG, a binary STL of each part, a text spec sheet, and a one-page PDF data sheet with a drawing, every dimension, a column for your measured values, the mesh analysis and the load rating. For a pair you also get an assembly DXF with both gears placed in mesh at the center distance. Every design also has a link that reopens it exactly.
Can I send my own STL or STEP file?
Not through the site yet. Email orders@protogears.com with the file and quantity and we'll quote it.
Do you make metal gears?
Nitronic stainless gears for corrosive and galling-prone service are in development. Sign up on the home page to hear when they launch.
Can I use the DXF files commercially?
Yes. Files you generate are yours to use however you like.